Search Documents

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By Thomas T., Read

DESIRABLE as it is to summarize what has been set forth in preceding chapters, the task can only be approached with great hesitation. What follows represents the personal views of the author at the moment of writing, reserving the privilege to change them on more mature reflection or in the light of further evidence. With that reservation they may be stated somewhat as follows. Education for the mineral industries falls into two categories; general education and technical vocational, using the word vocational not in its usual sense but to signify preparation for specific activities, in which sense a law school is a vocational school. Even at the beginning, as indicated in the first chapter, mineral industry education was partly general and, partly technical and that relationship still persists, because technical education requires a firm basis of general education. Our general American system is to provide free public' general education through the twelfth grade, or completion of high-school work, though there are already many technical vocational high schools, and even in a community where nearly all the young people are preparing for entrance to college there will be some who wish to qualify for employment at the end of the high-school course, or even on completing junior high. Our educational system, therefore, has not only to provide education for those who intend to proceed beyond the twelfth grade but also for those who, for a variety of reasons, may wish or be forced to cease full-time education at any level between the first and twelfth grades. This study has been chiefly concerned with the problem of what kind and how much technical education to provide for those who have completed the twelfth grade and who wish to make their living in the mineral industries. The obvious fact that the mineral industries employ all sorts of trained persons,

Jan 1, 1941

By Alexander Knoll, Dwight L. Baker

THE work herein reported shows that galena in certain organic solutions of fatty acids becomes coated with lead soaps, and that this coating is not only highly water-repellent but is also repellent to certain organic liquids, particularly those [ ] of high surface tension; i.e., nitrobenzene, diphenylmethane. WETTING PROPERTIES OF GALENA IN NONAQUEOUS FATTY ACID SOLUTIONS When a "captive bubble"' is withdrawn from a polished, plane galena surface under a nitrobenzene solution of stearic acid, the air bubble shows a decided tendency to "cling" to the mineral surface. The contact angle, therefore, was greater than zero, although it was not large enough to be measured quantitatively by the captive-bubble method.* [ ] When pure nitrobenzene was substituted for the nitrobenzene-stearic acid solution, no clinging of the bubble was observed; viz., contact angle = zero. Although the contact angle developed in air-galena-nitrobenzene-fatty acid solution was small, the organic solvent repellency of the galena surface was great enough to enable good recovery in a laboratory flotation cell.2 In Table I are given the results of flotation experiments using several different fatty acids dissolved in nitrobenzene.

Jan 1, 1941

Arizona ROBERT W. THOMAS, Chairman 'ROBERT W. HUGHES, Vice-Chairman HUBERT O. WOODS, Secretary-Treasurer American Smelting & Refining Co., Hayden, Ariz. FRANK A, WARDLAW, JR., National Director THOMAS C. CHAPMAN P. D. I. HONEYMAN CARL H. COLE JOHN E. LANNING. JOHN H. DAVIS JOHN C. LOVING EDW. G. DENTZER ALBERT MENDELSOHN MORRIS G. FOWLER BRENT N. RICKARD H. C. HENRIECHARLES F. WILLIS Black Hills BANCROFT GORE, Chairman N. P. GOODRICH, First Vice-Chairman C. N. KRAVIG, Second Vice-Chairman C E. SCHMIDT,

Jan 1, 1941

IN this survey of the progressive development of education for the mineral industries throughout the United States, the review of the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. PHILADELPHIA Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1853, when the Pennsylvania Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1850-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By Thomas T., Read

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for ,this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1893, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 30 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1893 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By Mario L. Villa

Argentina's oil production continues in its upward trend. The year 1940 closed with an important increase over 1939; that is, 1,996,371 bbl., or 10.72 per cent. The Government oil fields (Y.P.F.) are responsible for these results, as their total output was 12,474,655 bbl., which compared with the 10,222, 533 bbl. produced in 1939 represent an increase of 2,252,122 bbl., or 22.03 per cent. Fields operated by private companies yielded 8,134,882 bbl., against 8,390,633 bbl. in 1939, a decrease of 255,751 bbl. (3.04 per cent). To the total of 20,609,538 bbl. produced in 1940 in Argentina, the Comodoro Rivadavia field contributed 14,976,222 bbl.; Plaza Huincul, 1,275,814 bbl.; the Province of Salta, 1,845,1977 bbl. and the Province of Mendoza, 2,51I,475 bbl. Table 3 compares the output of companies working in Comodoro Rivadavia. The total increase of 186,819 bbl. (1.26 per cent) registered in the Comodoro Kivadavia area is due only to an intensification of development programs in the known

Jan 1, 1941

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1941 are available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS TECHNICAL PUBLICATIONS in Classes A-Metal Mining, 13-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets An Institute member is entitled to one copy of any printed TECHNICAL PUBLICATION or CONTRIBUTION Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will be sent upon request A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page, minimum charge, 25¢ Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1 25 domestic, $1 35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2 50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7 80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers) MINING TECHNOLOGY, $6 per annum domestic, $6 60 foreign (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6 60 foreign Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY Is mailed each month A member is entitled to one volume a year on his membership and he may purchase for $2 50 one copy of a volume not already received, additional copies of the same volume, $5 Nonmembers in the United States may purchase the volumes listed at $5 each, outside of the United States and its possessions, $5 6o Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members, to nonmembers 50¢ current issue and $1 each, back issues Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4 00 foreign.

Jan 1, 1941

By Marshall B. Standing, Donald L. Katz

DENSITY data are reported on 16 saturated hydrocarbon vapors at pressures ranging from 1000 to 8220 lb. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. INTRODUCTION The densities of natural gases are necessary in many engineering computations in petroleum production and utilization. Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 lb. per sq. in.4 Recent discoveries of pools having pressures up to 7500 lb. per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data on gas density at high pressures. METHODS OF COMPUTATION The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The methane-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by Sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir or while on contact with liquid during flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those considerably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions. This paper reports the density of 16 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure' have been modified and enlarged. A simplified method of obtaining gas density is presented in the form of charts, which apply for specific groups of gases.

Jan 1, 1941

By L. W. Kempf, K. R. VanHorn

PLASTIC deformation of most commercial metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful estimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. DETERMINATION OF RESIDUAL STRESSES The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.1 Fig. I reproduces some of the data

Jan 1, 1941

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By D. P. Morton

SINCE 1023, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (I) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.' This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as loo, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods. Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. 2 (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should he the same. It is neces-

Jan 1, 1941

By C. M. Romanowitz, H. A. Sawin

PLACER dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. DEEP DREDGING At Hammonton, Calif., Yuba Consolidated Gold Fields has, within the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 8o ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7 ½ -cu- ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1941

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system.

Jan 1, 1941

By J. W. Ristori

During the year 1940, production of crude oil in RiIexico totaled 43,914,000 bbl., or 2,776,000 less than in 1937, the year before expropriation. The 1940 output was I,2000,000 higher than in the previous year. In 1937, Poza Rica production accounted Declines in exports of Panuco crude, fuel oil and gasoline were recorded but these were more than offset by increased exports of 4,000,000 bbl. of Poza Rica crude, which was the approximate amount shipped to Sinclair during 1940 under the terms of the settlement. Over-all exports increased by 1,500,000 bbl. over the preceding year. The outstanding development regarding the destination of Mexican exports in 1940 was the increase of I0,000,000 bbl. in the exports to the United States. Exports to Germany ceased toward the end of '939 and to Italy in the second half of 1940. During the year 1940 the Sinclair interests and the Mexican Government settled their expropriation question. By the terms of the settlement Sinclair is to be compensated by cash payments and oil-purchase contracts. On Dec. I, 1940, Ada Camacho was inaugurated President of Mexico for a term of six years. Among his first acts following his election were: I. A proposal to change the Constitution to restore Supreme Court Judges' terms to life tenure. This has been ratified by both chambers of the Mexican congress and is now before the legislatures of the States of Mexico for ratification. The, taking away of the administration of the railroads from labor and restoration to the State.

Jan 1, 1941

By Harry H. Angst

THE history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 ½ -cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: 1. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By W. B. Lewis, M. C. Leverett

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,' water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

THE importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature." PREPARATIONS OF SPECIMENS In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal frictions is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm. Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tensiontesting machine, using special grips10 to ensure axial application of the load. The rate

Jan 1, 1941