Search Documents

Jan 1, 1942

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

There are no authentic records of production prior to 1869, although various records report local production and use in 1853 and 1860. Tonnages in Table 68 for the years 1853-1868, both inclusive, are estimated. [ ]

Jan 1, 1942

ALTHOUGH I have told you before (in the chapter on making the main mould for guns) how to support the core, I wish to repeat it here briefly and in a more orderly fashion, so that you may understand it better. For it is a thing of great importance to the profit of the owner as well as to the honor of the master, because he who does not locate the core in the middle makes the gun weak and incapable of shooting straight, and shows great lack of skill as a master. In short, it is very necessary to do this well. The first of these methods that I described to you is an iron, one dito wide, made into a ring which has four arms in a cross, or sometimes three. This is put in the mould where [88v] the last cornice begins, one palmo or half a braccio from the foot. Secure it in the middle of the diameter,

Jan 1, 1942

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction .within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress.4,5? The theory of recrystallization is not in advanced state; if recrystallization data were obtained, in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

[ ]

Jan 1, 1942

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By W. N. Lacey, R. H. Dourson, B. H. Sage

THE compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and 220°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. The experimental results are presented in tabular form and a number of diagrams illustrating the phase behavior of this system have been included.

Jan 1, 1942

By D. B. Kibler

The Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Alber-tus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. Early Mining The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to I-yd. capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas power- I house near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939 approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore 1 they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for I the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today i only three companies are operating. These

Jan 1, 1942

By C. P. Parsons

CALIPER logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork.

Jan 1, 1942

Early data about the amounts of coal used in making coke, and even of the first oven plants are meager. Table 84 shows the data about beehive ovens from 1841 to 1940, inclusive, and Table 85 shows the data about byproduct ovens from 1895 to 1940, inclusive.

Jan 1, 1942

LET us return and follow our first intention of discussing the art of melting. Since I have demonstrated to you how large works are made, you may have thought that the way to the small ones was also open to you, and you would not have been mistaken. But in order to avoid work and expense there are shorter and easier ways to be used, both because the things can be handled more easily and because it is not necessary to have so much regard for the forces of small materials. Therefore, wishing to make a distinction for you, I shall call this the small art of casting. Before speaking of this, I shall tell you of several methods of making powders for moulding. Then I shall also tell you of the methods of moulding in boxes and in frames, and how the said powders are to be prepared for casting either dry or green. Then I shall tell you some methods that are held as secret by the masters for handling the metals in melting and making them flow readily, so that you may easily fill the cavities of your moulds.

Jan 1, 1942

United Engineering Trustees, Inc. W. D. B. HOTTER, JR., '44 A. L. QUENEAU, '45 ALBERT ROBERTS, '43 The Engineering Foundation GEORGE D. BARRON, '44 F. F. COLCORD, '46 A. L. QUENEAU, '45

Jan 1, 1942

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1922. FEDERICO GIOLITTI Torino, Italy. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1941. DANIEL COWAN JACKLING San Francisco, Calif. 1939. HENRY KRUMB New York, N. Y. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1942

By F. McIntosh Galbraith

THIS paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application.

Jan 1, 1942

Jan 1, 1942

THERE are, as I have heard, varying opinions among men experienced in minerals as to whether silver has its own mineral [i.e., occurs native] or not. Mineralogical reasons and the authority of the majority persuade me that it has, not only because I have seen the natural material separate but also because I know that in mines of gold, copper, lead, and other metals pieces of pure metal are found without admixture, and I have heard that pieces of silver, gold, and copper have been found that had been reduced to their ultimate purity by natural causes. This is also confirmed by a German, Georgius Agricola, who says* that in a mine in Saxony a piece of metallic silver was found so large that the Duke who was prince and patron of the place had a whole dining table of square German style made from it without its being enlarged or worked on by any human artifice except for the tripod legs, and he often boasted that in this he surpassed the greatness of the Emperor. In truth I have never seen any metal except copper that was brought out from the mine pure and without any mineral, but I think that such a thing is indeed possible, since I believe in the greatness and power of Nature, who strives toward no other goal than perfection and purity. Indeed most of the minerals that I have seen have not been without admixture, not only of their earth but also of other metals, and this is more true of that which I have heard called silver than of any of the others. I except the silver that is mined in Schio in the region of Vicenza. These doubts, therefore, are not born without some shadow of apparent reason. As I told you above I believe that silver may have and does have its own mineral, for every substance that is converted into metal can exist pure by itself in its own species, as it also exists separately even though it be mixed with others, since it is seen that in each ore its metal is generated in a single body. Therefore it happens many times that whoever speaks of the ore of silver in one breath, without distinction, speaks of that of all the other metals, because there are few ores that are not mixed. But because the most noble things always have the prerogative of including in their name that of the others, where there is gold or silver the ores are not called

Jan 1, 1942

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942