Search Documents

By M. A. Mekicha, M. B. de Rooij, C. Pelletier, D. T. A. Matthews

One of the main factors that reduce strip cleanliness are iron fines, which are formed due to the abrasive interactions of the roll surface and the strip in the roll bite during cold rolling. They can cause a problem in fouling of the cold rolling mill as well as downstream processes. It has been repeatedly observed that chrome plating the work roll improves strip cleanliness. In the present work, scratch tests and reciprocating sliding tests were carried out under lubricated conditions to explore the influence of chrome plating on iron fines formation. Scratch tests were conducted to study the influence of chrome plating on iron fines formation at single asperity scale due to its intrinsic property. Reciprocating sliding tests were performed to study the influence of chrome plating a rough surface on iron fines formation, taking into account the initial roughness. The scratches made using chrome plated pins showed lower friction, generated less iron fines and exhibited lower material transfer. Reciprocating sliding tests done using the uncoated pins showed galling at different sliding distances depending on the roughness of the pin. On the contrary, reciprocating sliding tests with the chrome plated pins exhibited no galling irrespective of the roughness.

Oct 1, 2019

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

By Norbert Asamer, Stefan Purrer

Depending on the product or the material grade, conventional deburring machines, such as e.g. with rotating hammers, are in many cases not capable to reliably or completely remove burrs from the edges of a continuously cast product. Burr, however, is generated at the front and/or tail ends of a slab, bloom or billet as a result from torch cutting. Likewise, traversal grinding of the slab’s rolling surfaces can also cause burr at the long side edges of the slab whereby such burr can even be more difficult to remove. Based on their experience and know-how with abrasive machining processes (abrasive cutting, high-pressure grinding) over a period of more than 50 years up to now, BRAUN has developed a highly flexible deburring grinding machine for applications which are too difficult for conventional deburring techniques. BRAUN’s deburring grinding machines were successfully introduced to the steel industry and have proven their worth under normal production conditions already. The subject paper describes the key features and advantages of BRAUN’s machine design and the operational results from the first already completed projects.

Oct 1, 2019

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Anderson Ayres Bittencourt, Sergio Valle Junior

Um dos grandes desafios nos ambientes industriais é o monitoramento contínuo de aplicações de automação. O difícil acesso a redes industriais e os sistemas legados trazem grande complexidade a esta tarefa. Para resolver o problema, a migração destes sistemas e redes para arquiteturas mais novas e integradas é essencial. E essa migração permite o uso de ferramentas antes só conhecidas no mundo de TI para apoiar o processo industrial trazendo clareza e assertividade na análise de falhas, troubleshoot e monitoramento integrado de todos os sistemas. Traremos neste trabalho um esclarecimento de como foi o modelo implementado nas plantas de Tubarão e Vega e diversos detalhes sobre cada componente escolhido com o propósito de prover uma solução fim-a-fim para o monitoramento de aplicações e ativos de Nível 2 e Nível 1 da Automação.

Oct 1, 2019

By Camila Fernandes Rezende, Camila Simon Christ, Vinicios Andreatta, Marcus Vinícius Pimentel Gomes

A integração e cruzamento de dados de diversos sistemas para as unidades técnicas de processo sempre foi uma necessidade e um desafio. Para a unidade técnica da Aciaria, a integração de dados gerados pela Instrumentação, Automação e MES (Manufacturing Execution System) é imprescindível para a análise e otimização do processo. Este processo feito de forma manual era trabalhoso, improdutivo e com grande potencial de erros. Mesmo com o suporte da área de TI (tecnologia da informação) e TA (tecnologia de automação), em alguns casos este processo era inviável devido à complexidade. Com a utilização de uma ferramenta analítica, já utilizada em outros processos produtivos da empresa (Laminação de Tiras a Quente e Qualidade), foi possível prover acesso a diferentes bases de dados, permitindo a integração dessas informações de forma simplificada, ágil e única, todos consumindo os mesmos dados, com as mesmas regras. A automatização deste processo trouxe benefícios como: melhora na qualidade do dado, democratização das informações e tempo para investigação de problemas e otimização de processo, além de menor dependência das equipes de TI e TA.

Oct 1, 2019

By Luciano Henrique Andrade de Resende, Maria Rita Oliveira Rebouças

O processo de Monitoramento Controles, realizado pela área de Governança, Riscos e Compliance, requer preparação e verificação de um grande volume de dados. Isso feito de forma manual e com a necessidade de cruzar dados de diferentes fontes, torna o processo bastante complexo, impactando diretamente na periodicidade e acurácia dos testes. O objetivo de trabalho era prover uma ferramenta e uma metodologia que fosse capaz de automatizar esse processo, tornando-o contínuo e possibilitando análise de uma grande massa de dados, proveniente de diferentes fontes e com uma saída padronizada. Após análise de ferramentas de mercado e a realização de provas de conceito, foi definida a ferramenta e modelo de trabalho a ser aplicado. O resultado foi a implantação de um processo de Monitoramento Contínuo de Controles (MCC) que traz: ganho de produtividade, ao permitir que testes sejam executados de forma automática; ganho de eficiência, por permitir realizar o teste em toda a base de dados, sem necessidade de amostra; aumento na assertividade, por reduzir probabilidade de erro humano provenientes de atividades manuais; além de retorno financeiro e mitigação de riscos.

Oct 1, 2019

By Herman Pessoa Lima Júnior, José Brant de Campos, Rodrigo Felix de Araujo Cardoso, Paulo Renato Barbosa Marinho, Rauni Coelho da Costa

A técnica de SAXS é um método analítico que possibilita a determinação de diversas propriedades em nanomateriais, onde o colimador é a parte mais importante da óptica deste tipo de equipamento, sendo sua fabricação um desafio. Software de CAD 3D e 2D foram utilizados no desenvolvimento e fabricação de um bloco de colimação e testes comparativos foram realizados com fontes de raios X. Os testes mostraram que a geometria do feixe colimado é condizente com os modelos geométricos previamente resolvidos.

Oct 1, 2019

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Edilson Alves Maranhão, Willi Anton Buehler, Andrea Pezza

O processo de vácuo é a solução típica aplicada quando é hora de atualizar o nível de qualidade do aço de uma aciaria existente. A instalação do novo Tanque de Desgaseificação à Vácuo (VD) de 135t no Canadá e do novo RH de 150t na planta integrada no México para a produção de tubos de alta qualidade na América do Norte é um exemplo típico disso. A nova instalação inclui o mais recente conceito de design para este tipo de equipamento: operações totalmente automatizadas e menor impacto ambiental são os principais aspectos do projeto. A solução de bomba mecânica a seco continua sendo a melhor abordagem de investimento e custo operacional para a tecnologia de vácuo. Os principais aspectos do design da planta são descritos neste documento. O desgaseificador a vácuo VD é responsável pela melhoria das performances metalúrgicas, especialmente em termos de nitrogênio, remoção de hidrogênio e nível de pureza do aço. O processo a jusante e os resultados estão estritamente ligados aos desempenhos do desgaseificador a vácuo. O monitoramento de processos através da linha completa é uma prática padrão para obter uma melhoria efetiva da qualidade do produto. Os desempenhos metalúrgicos do desgaseificador a vácuo VD são analisados e comentados neste trabalho.

Oct 1, 2019

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By Gabriel Duarte de Andrade, Arnaldo Veronêz Júnior

Em um processo de sinterização, a velocidade da máquina de sínter deve ser controlada, com o intuito de garantir que o ponto final de queima da camada a sinterizar esteja dentro de uma faixa que possibilitará elevada produtividade. Este artigo apresenta um modelo físico que descreve o movimento da frente de queima da camada ao longo do leito e o controle de velocidade implantado no sistema de automação de nível 2 da Sinterização da ArcelorMittal Tubarão. O controle de velocidade foi proposto para manter o ponto final de queima em torno do valor do setpoint escolhido. Ao longo dos anos, as condições operacionais da planta de sinterização mudaram em razão da variação da qualidade dos minérios que compõem a mistura. Nesse contexto, o controle foi avaliado e apresentou resultados satisfatórios, permitindo à operação uma forma de controlar o processo sem adicionar atrasos relacionados à tomada de decisão.

Oct 1, 2019