Search Documents

By M. R. Paterson, M. K. Suddaby

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a continuous elution process is established and the development of a large-scale pilot plant is described. It is based on a continuous elution apparatus that has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra, and other methods of elution. The performance of the atmospheric continuous elution system (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1988

By M. R. Paterson

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a Continuous Elution Process is established and the development of a large-scale pilot plant is described. It is based on a Continuous Elution apparatus which has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra and other methods of elution. The performance of the Atmospheric Continuous Elution System (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1986

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982

By M. A. Schimmelpfennig, A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to longer travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation may be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways may contribute to formation. This study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Co. to identify causes of the problem.

Jan 1, 1984

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By Houyuan Liu

A new process was developed to recover nickel and cobalt by leaching laterite ore at atmospheric pressure and.95"-105" C. The nickel-containing goethite in limonite was first leached with sulphuric acid to liberate over 90% of nickel, cobalt and iron. The dissolved iron was then precipitated as Ni-free goethite by the additioil of saprolite. The acid released during iron precipitation as goethite was simultaneously used as lixiviant to leach saprolite to recover more nickel. With this process the limonite and saprolite were essentially converted into goethite-, gypsum- and silica- containing tailings. Twenty bench scale tests and two campaigns of pilot plant operation were carried out at BHP Billiton's Newcastle Technology Centre (NTC) from January to August 2002. The overall nickel and cobalt extractions were 81 to 90% and 91 to 100% respectively. The average plant availability was 99%. The advantages of this process over existing processes include high plant availability, high consistency, robustness and simplicity of the operation.

Jan 1, 2004

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By James P. Kimball

BY the term weathering of coal is meant the process of deterioration to which under various circumstances it may be exposed at ordinary temperatures, both from outward agencies on the one hand, and on the other hand from its own constitutional qualities. This process involves along with some minor qualitative changes certain quantitative changes resulting in a gradual and limited reduction in the quantity of the organic elements, and relatively a corresponding increase of its inorganic or mineral constituents as represented by its ashes, and often in an increase of the absolute weight of the coal. In common with many mineral substances, coal absorbs oxygen

Jan 1, 1880

By L. M. Sekhukhune

The atmospheric leaching of copper-bearing matte by acidic ferric chloride solution was studied at the laboratory scale. The aim was to achieve maximum copper and nickel recovery by investigating the mechanisms of leaching, as well as identifying the effect of temperature, and concentration of ferric chloride and oxygen. Djurleite (Cu1.96S), hazelwoodite (Ni3S2), and Ni alloy were the primary phases detected in the matte. The quantitative composition of the matte was Cu 31%, Ni 50%, S 13%. Fe and Co constituted 2%, with platinum group metals (PGMs) accounting for 0.5%. A maximum nickel extraction of 98% was achieved using two-stage oxidative leaching at 90°C and 11 g/L Fe3+ as compared to 65% under non-oxidative conditions. A copper extraction of 99% was achieved in the first 45 minutes using two-stage non-oxidative leaching, and copper was recovered from solution by cementation. Three processes took place simultaneously throughout the leaching process, namely: dissolution, cementation/ metathesis, and oxidation. The leaching process was found to be diffusioncontrolled.

Jan 1, 2014

By N. Panagiotopoulos

A low-grade (1.06% Ni, 0.06% Co) hematitic type lateritic ore from Triada, Euboea Island, Greece, has been leached with sulfuric acid at atmospheric pressure for the extraction of the contained Ni and Co values. The effect of various parameters, including reaction time and leaching temperature, acid strength, pulp density, etc., on Ni, Co extraction and Fe dissolution was determined. By leaching at 95°C for 4h with a 3N sulfuric acid solution at 25% pulp density, Ni and Co extractions were 82 and 75% respectively, and Fe co-dissolution 28%, yielding a pregnant solution containing 2.7 g/l Ni, 0.16 g/l Co, and 33 g/l Fe. Overall acid consumption was 850 kg/t ore (or 100 kg/kg Nil. Preheating of the laterites at 600°C before leaching resulted in much faster leaching kinetics for Ni, but the final extraction and acid consumption remained unaffected; Fe extraction was not influenced. Three-stage counter-current leaching at 9S°C, using 2N acid strength at each stage and 35% pulp density, reduced acid consumption to 350 kg/t ore (41 kg/kg Nil, and yielded 81% Ni recovery. Percolation leaching of -10 mm laterite at ambient temperature with 3N acid for 7 days resulted in 58% Ni extraction.

Jan 1, 1988

By W. D. Felix, R. D. Smith, J. A. Campbell

The mechanism most consistent with available information on atmospheric trace element emissions involves the volatilization of a significant fraction of many trace elements during coal combustion, with subsequent condensation on fly ash as the combustion gases cool. The larger surface-td-volume ratio of the smaller particles leads to an enrichment of the volatile trace elements. From an environmental viewpoint, the submicron size particles are of greatest concern. These particles show the highest concentrations of trace elements, are least efficiently collected by pollution control devices, have high atmospheric mobilities, and are deposited preferentially in the pulmonary and bronchial regions of the respiratory system. The mechanisms for trace element enrichment and formation of submicron particles will be described.

Jan 1, 1981

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957