Search Documents

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

The typical reactions which the reductants undergo during ferroalloy production are reviewed, and identified as reaction with CO2 and with SiO, and dissolution in metal. Available reactivity tests for these three reactions are reviewed. It is proposed that it is worthwhile considering dissolution kinetics as a reactivity parameter. Greater crystallinity of the reductant decreases CO2 and SiO reactivity, but increases dissolution rates.

Jan 1, 2002

By B. McCosker

The choice of the appropriate delivery process for a project is often not adequately thought about. The industry needs to be prepared to break its preconceived mind-sets on delivery procedures. Industry should also be prepared, on a project by project basis, to commit to a critical review as to how the assessment and then selection of the best procurement method can best optimize the project outcome for both client and contractor. Conventional standards and biased reliances and experienced based preferences should be challenged. To achieve this requires a paradigm shift in attitude to both the process of tendering and the evaluation of tenders. Tender and contracting practices are dynamic and have moved away from solely cost based assessments. Tendering contracts arise imposing changed duties upon owners. Traditional contract delivery models have shifted, reflected in part by the trend towards relationship contracting. The categories of contract options are not closed. Many are but hybrids of other time-tested models. This paper considers options available for any brownfield or greenfield project. The principles outlined are translatable to supply, upgrade, operation and maintenance arrangements.

Jan 1, 2002

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By R. G. B. Pickering

The hard rock gold and platinum mines in South Africa have seen little development in the technology of mining. Holes are still drilled in the rock?though the latest water hydraulic rockdrills will complete that task in two minutes compared with the eight hours for hand drilling. Charging up is with far safer explosives and with available initiation systems it is no longer necessary to run up the face lighting each fuse. Movement of rock in the stope is predominately by means of scraper buckets and scraper winches?these were first introduced in the 1920s. Support is still mainly rock, either in situ pillars or backfill, or alternatively wood. Just as the mining process has changed very little it is hardly surprising that the productivity of mining is also relatively unchanged. Major efforts have been made to mechanize the mining process. However, most of the narrow reef mines where ?trackless mechanized mining? was introduced in the early1980s have reverted to conventional mining. In the wider reefs mechanized mining is the option of choice, unfortunately most of the gold and platinum mines have very narrow reefs that are not suitable to ?off the shelf? equipment. The move to introduce room-and-pillar mining into the narrow UG2 reefs is at the expense of mining more waste with the reef, fortunately it appears that appropriate waste and reef separation processes are available. Room-and-pillar mining followed by long hole drilling and blasting of a narrow slot of reef out of the pillars currently appears to offer the best of both worlds?maximum reef recovery with minimum waste dilution.

Jan 1, 2002

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By P. C. Schutte

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator?s function is now essentially one of control rather than being an energy source, however, the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialized area of mechanized mining.

Jan 1, 2002

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The stability of a ferrosilicon dense medium suspension is one of the most important parameters to keep under control since it determines the density gradient of the medium in the separation zone and thus directly influences separation sharpness. The stability of ferrosilicon suspensions were characterized using settling tests employing a differential pressure method. Particles smaller than 45 µm and especially the ore fines played an important role in the settling behaviour of the solids. High medium stability is favoured by ore fines, fine medium particles, and high medium densities. Keywords: dense media, ferrosilicon, dense medium stability, ore fines

Jan 1, 2002

The Modified Zincex® Process, developed by Técnicas Reunidas, is highly flexible dealing with a wide range of pregnant leach solutions. No matter if those solutions are produced from primary or secondary raw materials, and/or are based on conventional leaching, pressure leaching, heap leaching or bio leaching the result is always high-purity zinc product. The zinc solvent extraction unit within the process is a very effective barrier for impurities and a buffer for the composition of the pregnant liquor. This unit achieves an extremely pure aqueous extract that can be converted into different final products. All of them are characterized by fulfilling the highest purity standards. Also, there is the possibility to adapt the global process to a wide range of pregnant liquor compositions and various production capacities up to a zinc production limit over 150 000 t/a with a single solvent extraction plant.

Jan 1, 2002

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By J. H. Potgieter

The method used to assess the reactivity of lime was evaluated to gauge it usefulness as a quality control tool. The effect of particle sizes, different lime and water masses for a fixed s:l ratio and the same for various s:l ratios on the reactivity values obtained, were investigated. An attempt to introduce the amount of grit produced during the slaking reaction as an additional measure of limeís quality and reactivity, proved to be unsuccessful. It was also found that the relative amount of lime slaked during the different tests was independent of the reactivity value of the lime. The investigation confirmed the usefulness of the accepted test procedure as are liable method to measure the reactivity of lime, despite various reservations expressed from a theoretical point of view.

Jan 1, 2002

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By P. J. van der Walt

The paper1(hereinafter BG) by two respected sampling experts contains sound theory and logic that can?t be directly refuted. Nevertheless, a practitioner knows that there is a broader context in which the practice of sampling takes place. This broader context, being less well defined than the theory of correct sampling, receives correspondingly less exposure which this commentary??prompted by? BG?seeks to rectify. ?Correctness? of a sampler is the central concern of BG, where it is presented as a sharp ?black-and-white ?distinction. Accordingly, comments below are grouped under the following headings: ?Correctness in practice ?Without correctness, what can be done? ?The broader context.

Jan 1, 2002

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002