Part VII – July 1968 - Papers - Morphological Study of the Aging of a Zn-1 Pct Cu Alloy

A number of experimental rnethods—X-ray powder diffractometry, Laue photography, X-ray small-angle scattering, and transmission electron microscopy and dijfraction—have been utilized to examine the morphology associated with precipitation from the terminal, g, solid solution of a Zn-1 pct Cu alloy. A significant age hardening was observed in a 1 pct Cu alloy. X-ray and electron diffraction results showed that the structural inhomogeneities associated with the hardening were isotructural with the matrix. The average size and shape of the inhomogeneities were deduced from the electron microscopy and X-ray small-angle scattering. The preprecipitates are hexagonal platelets some 300? in diam. and some twelve unit cells thick. The orientation of the platelets was deduced from Laue photographs and electron diffraction. The platelet plane is (0001). When a large amount of pre-precipitation is present in a localized volume the new lattice is often disoriented by a rotation about (0001) of of the matrix. WhILE dilute Zn-Cu alloys have been commercially important for some 50 years, relatively very little is known metallographically about this material. The "Zilloys", zinc with about 1 wt pct Cu and sometimes a small addition of magnesium, are used to produce rolled zinc which is harder and stronger than that produced by other rollable zinc alloys.' According to the phase diagrams of the zinc-rich side of the Cu-Zn system, such dilute Zn-Cu alloys should age-harden;2-5 the solubility of copper in zinc, g-phase, at 424°C is 2.68 pct, while at 0°C it is only to 0.3 pct. However, the published literature on the aging of this system appears to be limited to a documentation of the contraction of 1, 2, and 3 pct Cu alloys aging at 95°c,6 and an attempt to measure changes in lattice parameters during aging.' In the latter work, no lattice parameter changes were detected, although a broadening of the highest-angle lines was detected and considerable diffuse scattering was observed. Micro-structural investigations have been limited to the latest stage of aging, wherein Widmanstatten precipitates are formed.3,47 These alloys are of interest for still another reason. The two most zinc-rich phases in the Cu-Zn system, 77 and E, are both hcp. Moreover, the change in a, between 17 and t for a 1 wt pct Cu alloy is onlv 3.64 -,~ct: the change in Co is 12.0 ict. It would be anticipated that precipitation in such a material might occur through metastable phases or G.P. zones with epitaxy along mutual 0001 planes. The goals of the present work are aimed at partially filling the void of knowledge concerning the early stages of precipitation from the g phase. In particular, we have attempted to document the magnitude of the age hardening of this system and to determine the size, shape, and orientation within the matrix of the elements of precipitation in an early stage of condensation. EXPERIMENTAL A) Specimen Preparation. Specimens were prepared In two somewhat different ways, one method being used for X-ray Laue and diffractometer measurements, optical microscopy, and Rockwell hardness measurements and the other used for electron microscopy and X-ray small-angle scattering. In the first case zinc and copper in the proper proportions to yield a 1 wt pct Cu alloy were melted together in a closed graphite crucible. Castings so made were free of apparent segregation or oxidation. The castings were then solution-annealed at 400°C for several days and then quenched in water to room temperature. Filings of portions of the specimens were made for use as X-ray powder diffractometry specimens. The electron microscope material was made as follows. Castings were made under vacuum with copper powder placed inside a hollow zinc cylinder to insure good contact of the materials. These 1 wt pct Cu pieces were then rolled to 0.1 mm with an intermediate anneal in vacuo. The rolled sheets so formed were then annealed for about 6 hr at 225°C. Finally the specimens were electropolished slowly until thin enough for transmission electron microscopy. The polishing is discussed in greater detail in the Results section. B) Measurements. X-ray measurements of three types were performed. A G.E. XRD-5 diffractometer was used to examine powders of the alloy for identification of second-phase material. A Kratky small-angle camera, also operating from a G.E. tube, was used to investigate the sizes of small precipitate particles. In both cases, nickel-filtered copper radiation was utilized. Finally, individual grains of the large-grained castings were examined in the back-reflection Laue geometry. Electron microscope studies were carried out with a J.E.O.L. Model 6A instrument. RESULTS A) Hardness Measurements. Hardness measurements performed at room temperature on the large-grained polycrystalline specimens showed a hardening which was essentially complete in 3 hr. Fig. 1 shows a typical plot of hardness vs aging time. The relative magnitude of the ultimate hardening varied from run to run between 150 and 200 pct of the value for the material immediately after quenching from the solution anneal. Most probably the variations reflect small changes in the time taken to remove the specimen from the vacuum furnace after the solution anneal.