Institute of Metals Division - Titanium-Nickel Phase Diagram

The Ti-Ni phase diagram has been investigated up to 68 pct Ni with iodide titanium base alloys by metallographic, X-ray, and melting point methods, and from 68 to 90 pct Ni by examination of as-cast structures of sponge titanium base alloys. NVESTIGATION of the nickel-rich portion of the I Ti-Ni phase diagram was first reported by Vogel and Wallbaum in 1938.' This work was subsequently extended to lower nickel contents by Wallbaum' who indicated the possibility of a eutectic reaction for nickel contents below 38 pct. Long et al.3 studied the titanium-rich portion of the phase diagram and found eutectic and eutectoid reactions below 38 pct Ni. However, the temperature of the eutectic indicated by Long et al. was considerably lower than that suggested by Wallbaum. Long and his coworkers synthesized their alloys by powder metallurgical techniques and encountered oxygen and/or nitrogen contamination. Thus the diagram which was obtained did not represent binary alloying conditions. However from these results the features of the binary diagram were predicted. At Battelle Memorial Institute4 the Ti-Ni diagram was investigated up to approximately 11.5 pct Ni with sponge titanium alloys. The range of temperatures used was not sufficient to define the eutectoid temperature or composition. The data of Wallbaum2 and Long et al.8 were of particular interest for the present study, and although the work was originally concerned with the region below 40 pct Ni, the investigation was extended to higher nickel contents in an attempt to resolve the differences between these workers. Experimental Procedure Preliminary work on the Ti-Ni system was carried out with duPont Process A sponge titanium alloys to reduce the amount of subsequent work to be done with iodide titanium base alloys. The sponge titanium used contained 99.71 to 99.77 pct Ti, 0.1 pct Fe and 0.005 to 0.009 pct Ni. The iodide titanium obtained from the New Jersey Zinc Co. contained 99.9 to 99.95 pct Ti. Nickel used with sponge titanium was 98.9 pct pure. The high-purity nickel alloyed with iodide titanium was cobalt-free with approximately 0.05 pct C and was obtained through the courtesy of the International Nickel Co. The 15 g sponge titanium charges for melting were prepared by compacting in a die or by placing the weighed portions of nickel and titanium directly into the furnace. Iodide titanium charges were made by drilling holes in the as-received rod and inserting the nickel or by wrapping the nickel in sheet. Sponge titanium alloys containing from 0.2 to 90 pct Ni and iodide titanium alloys containing 0.2 to 68 pct Ni were prepared by these methods. In addition to these alloys several 1/2 1b sponge titanium alloys were supplied by the Allegheny Ludlum Co. The charges were melted in an arc furnace under an argon atmosphere. The procedures used were similar to those reported in the literature5,' and the furnace has been described.' Except for iodide titanium alloys with 40 to 68 pct Ni (see section on copper contamination), each alloy was melted for 1 min, then either turned over or broken before re-melting for an additional minute. Currents of 200 to 400 amp were used depending on the melting point of the alloy. Prior to heat treatment, alloys containing less than 14.5 pct Ni were hot-forged at 750°C. With the exception of alloys in the homogeneity range of the compound TiNi, alloys of higher nickel contents could not be hot-forged. Heat treatment of iodide titanium base alloys was carried out in argon-filled quartz capsules which were broken under water at the conclusion of heat treatment to quench the specimens. Temperatures were controlled to ±5oC and annealing times up to 48 hr were used. For melting point determination, specimens were placed in carbon crucibles which were in turn en-capsuled in argon-filled quartz capsules. The start of melting was determined by rounding of corners and by metallographic examination. Complete melting was considered to have occurred at that temperature at which the specimen assumed the shape of the crucible. Specimens were prepared for metallographic examination by mechanical polishing or by an electrolytic procedure." For alloys containing up to 80 pct Ni Remington A etch7 50 pct glycerine, 25 pct HNO,, 25 8 HF) was used. For higher nickel alloys aqua regia and Carapella's etch (5 g FeCl,, 2 ml HNO,, and 99 ml methyl alcohol) were employed. Specimens to be exposed for powder patterns were prepared by filing, by breaking specimens in a