Discussion of Mechanical Loading (d3ec5682-fcc6-4f70-8660-39bb84ee9f5a)

CHAIRMAN LITTLEJOHN: Some of the members will want to question Mr. Farnham on some of the things he has brought tip, so we will throw the meeting open for discussion. I am quite sure Mr. Farnham will be willing and glad to answer any questions that may be put to him. MR. HOLMAN: I would like to ask Mr. Farnham a question in regard to the Duckbill: How wide a face will it operate without moving the bill? MR. FARNHAM: The Duckbill is a device that was developed in the Union Pacific Mine at Rock Springs, within the last few months, and it is shaped something like, a dustpan, with discharge throat in the rear. They made one seven feet wide and found it was too wide, and the one they are using now is between three and four feet in width. The front section of the conveyor, which attaches to the duckbill, meshes into it to form a sliding section, and the front end of the Duckbill is pushed by the upper segments. I saw one used in a room twenty-four feet wide, and they drew it back after they cleaned out one room and pushed it forward again. MR. HOLMAN: You have no arrangement other than ratchet work? MR. FARNHAM: The ratchet is for forward working and back; the sections are made 12 or 13 feet long, and the stroke of the conveyor automatically works the ratchet; they can ratchet it back; it is a hand device. MR. HOLMAN: They just swing the end of the conveyor across the face to pick up the loose coal? MR. FARNHAM: Yes; they are also planning to use it endwise along the panel face, that and the room work both are quite new in their application, and I do not think the Union Pacific is giving out any results as yet, because the system has not been in use long. MR. HOLMAN: We are planning on putting one in very shortly. MR. HALL: I understand they can swing it over 30 degrees one way or the other, and it goes the same way easily because of the continual jar of the back and forward motion on a 60-degree swing. SECRETARY SHUBART: Take on a comparatively long conveyor, you can get quite a sweep, a large part of the circle. The Duckbill could command quite a large range. For a 12-foot entry, take a four-foot wide advance through the middle of the shot coal, with a 12-foot advance, ratchet back, swing the Duckbill to the rib and repeat; but I do not think they could get as much as 60 degree. on the end of the Duckbill without curving further back. The conveyor is light and not normally set on any permanent foundation. I saw one of Mr. McCarty's first machines, a rather rudimentary one, clean tip a 12-trot entry, 21 tons of coal, in 16 minutes, three men at the face and one at the loading end. MR. FARNHAM: The average time to clean the entries is about an hour-to clean up good-it wouldn't take but a short time; that is why they get this record of several cuts a shift. CHAIRMAN LITTLEJOHN: Are there any other questions you would like to ask Mr. Farnham? MR. HOLMAN: We were discussing this entry driving in regard to the entry loader; an entry loader in advance work, just what you have to do to place the jackbars with the sheave-blocks? Do you dig along the ribs after the coal is shot or do you have any other scheme that could be worked out to a good advantage? MR. FARNHAM: This record is a report I have just received from our Chicago office, without the full details, which I have written for. I am sorry I cannot give you the details. This was an Indiana or Pennsylvania mine, near Pocahontas, not the one where they had an accident. I assume they set the jacks ahead and swung and dumped the coal partly out with a scoop and partly by hand, but the application for that for entry driving is entirely new. The reports stated that they anticipated using that as a standard method of entry driving in the future. I will be glad to see that you get a copy of it when I get the report completed. MR. MONAY: Mr. Shubart, did you say they loaded 12 tons in 16 minutes? SECRETARY SHUBART: Twenty-one tons. MR. MONAY: How long did it take to change the machinery out of there