Discussion

MR. HARRINGTON: I would like to ask Mr. Bottomley if they fire their shots while the men are in the mine? MR. BOTTOMLEY: No sir; the shot-firing law in our State requires the shots to be fired after the men are out of the mine. We fire more shots than we did under the hand method of loading. Where formerly four holes were drilled, now we drill eight, using the same amount of powder as we did formerly, perhaps a little more, but we use a slower grade of powder. CHAIRMAN LITTLEJOHN: Any further discussion, gentlemen? MR. GIBSON: Mr. Chairman, I would like to ask Mr. Bottomley, if, in his shot-firing system, as I understand it, he has a very high coal and is working something like eleven feet? MR. BOTTOMLEY: Something like that. MR. GIBSON: I read the article that you referred to. Did you use both the first and the second delay explo¬ders in shooting the coal? MR. BOTTOMLEY: We use the ordinary fuse. MR. GIBSON: That is what I wanted to find out; whether you use the delay exploders and the detonators. In Utah, we are getting away from the fuse altogether, because we do not think it is accomplishing anything to use the electric light on the cap, and' at the same time shooting with fuse. We are defeating the object we might gain in using the electric safety lamp. That is a point that might be discussed a little further. MR. E. H. JOHNSON, The Coloder Company: I would like-since it is a general opinion that mechanical loading breaks up the coal, to ask Mr. Bottomley, if he finds a larger percentage of small coal, or how much, through the use of the mechanical loaders? MR. BOTTOMLEY: We do not find any great difference. In fact, we have succeeded in improving our lump coal percentage, and that is important, because it is largely domestic. At first, when the machines were installed, the boys shot the coal too hard, and we fell down a little, about two or three per cent, the first month, in our lump percentage, and we tightened up a little and changed our methods in shooting and got on to the stunt of drilling more holes and getting a slower grade of powder. We could not load as much coal in one day as we could before, but we did succeed in in. creasing our lump coal percentage four and a half per cent over the hand method, and that is quite a factor-quite an important factor and since our domestic trade is over with, we loosened up on the shooting and we are running about the same as we did with the hand loading, maybe a half per cent more, or one per cent, but pretty much the same. MR. SHUBART: Your coal is very high? MR. BOTTOMLEY: Yes. MR. SHUBART: Have you tried sunbbing the coal before shooting? MR. BOTTOMLEY: No, we have not tried that. It is very hard coal to shoot; we have no defined cleavage in our coal. It is the worst coal I ever saw to shoot. We do not try to snub it. Formerly, as I said, the miners drilled four holes, pretty well up near the top, and then four holes down, within about three feet of the bottom. It is the same thing as a snub shot, and that we find is the best method for shooting the coal. We have not tried any mechanical device for snubbing as yet. SECRETARY SHUBART: At one mine I saw snubbing tried with a Jeffrey undercutter with a seven-foot Jeffrey bar. This mine, by the way, is very similar to Mr. Bottomley's condition. They have very high coal, so the snub cut is a small percentage. They cut a seven foot undercut and raise the machine on an eight inch tie and undercut five feet to give the effect of a snub cut, 14 inches at the front of the cut, and then six inches at the back of the cut. They made a very marked increase in lump. (The bug dust would be a small percentage of the total coal), and they increased the percentage of the slack at the same time. They found a decrease by reason of the easier shooting of about 15 per cent in their slack. In other words their nut and lump coal ran considerably higher and their slack decreased 5 per cent with the snubbing cut. Mr. Bottomley, I believe, understands those conditions.