If you have access to OneMine as part of a member benefit, log in through your member association website for a seamless user experience.
|Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.|
Additional chapters/articles from the SME-ICGCM book 24th International Conference on Ground Control in Mining (ICGCM) 24th
|Keynote Address at the 23rd International Conference on Grou||Analysis and Design of Rib Support (ADRS) a Rib Support Desi||Evaluation of the Impact of Standing Support on Ground Behav||Half a Career Trying to Understand Why the Roof Along the Lo||Forecasting Roof Falls with Monitoring Technologies - A Look||Analysis of Seismic Source Parameters of Roof Falls in Time||A System to Provide Early Warning on Impending Goaf||Outcomes of the Landmark Longwall Automation Project with Re||Application of Phenolic Foam in Longwall Mining||Multiple Seam Mining Interactions: Case Histories from the H||Analysis of Entry Stability Associated with Multi-seam Minin||Failure Mechanics of Multiple Seam Mining Interactions||Engineering Classification of Ultra-close Multiple Seam Roof||Definition of Ultra-close Multiple-seams and its Ground Pres||Depillaring and Roof Bolting Practices at Quinsam Coal Mine||Seam Structure - An Important Criterion for Coal Pillar Desi||Mitigating Longwall Subsidence Effects on a Large Industrial||Impacts of Longwall Mining on Hydrology, Soil Moisture, and||Basics on the Dimensioning and the Extraction of Shaft Safet||Modeling the Arc-effect of a Coal Mine Roof||Recent Advances in Numerical Simulation of Cutter Roof Failu||Test Method for Assessing Water Degradation Potential of Coa||Geotechnical Strata Characterisation Using Geophysical Boreh||A Method for Quantitative Void/Fracture Detection and Estima||Implication of Highly Anisotropic Horizontal Stresses on Ent||Ground Control of a Mine Stope in Weak Rocks Subjected to Hi||Analysis of Highwall Mining Stability - The Effect of Multip||Highwall Mining in a Multiple-seam, Western United States Se||The Slope Stability Assessment in the Wall Overlooking the S||Numerical Modeling as a Tool to Predict Pillar Condition and||Development and Testing of a New Roof Prop||Stability Mapping System||Using Foaming Grout to Stabilize a Ventilation Raise in Very||Roof Control and Roadway Support Design in the #9 Coal Seam,||Non-confirmation Mathematics for Wall Rock Classification fo||The Influence of the First Layer Thickness of Immediate Roof||Studies on Distribution Pattern of and Methane Migration Mec||Development of a New Roof Bolt Technology to Improve Gate- R||Improved Pull out Strength of Fully Grouted Roof Bolts throu||Experimental and Numerical Methodology Assessment of Load Tr||An Investigation into the Support Systems in South African C||Investigation of Fully Grouted Roof Bolts Installed Under In||Development of the Laboratory Short Encapsulation Pull Test||A Resin Quality Testing Procedure for Collieries||Determination of Load Transfer Characteristics of Gloved Res||Fully Grouted Torque Tension Bolts Successfully Support Pitt||Shear Bond Characteristics in Grouted Cable Bolts||Overcoring Techniques to Assess in Situ Corrosion of Galvani||Development of a Laboratory Facility for Testing Shear Perfo||Mechanical Response of Split-Set Rock Bolts in Squeezing Gro||Mechanisms of Rib Sloughing and Methods of Controlling Thick||Supporting Method of the Bolted Strata in Large Deformation||Assessment of Ground Conditions Near a Mine Portal Using Gro||Detection of Abandoned Mines and Air Passages/Burning Center||Detecting Abandoned Coal Mine Entries by High Resolution Ear|