Field Test with Strain-gauged Friction Bolts at the Gold Hunter Mine, Mullan, Idaho, USA

Johnson, Jeffrey
Organization: International Conference on Ground Control in Mining
Pages: 7
Publication Date: Jan 1, 2003
To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.
Full Article Download:
(1711 kb)


Additional chapters/articles from the SME-ICGCM book 22nd International Conference on Ground Control in Mining (ICGCM) 22nd

Pillar Design and Roof Support for Controlling Longwall Head
Stress Analysis and Support Design for Longwall Mine-Through
The Utilisation of Numerical Modelling to Predict Water and
Longwall Roof Fall Prediction and Shield Support Recommendat
Comparison Of Multiple And Single Entry Roadways For Highly
Numerical Modeling Of Longwalls In Deep Coal Mines
The Characteristics Of Mining-Induced Fractures In Overlying
Design And Experience Of Total Extraction Room And Pillar Op
Using Site Case Histories Of Multiple Seam Coal Mining To Ad
Mining Method For Extracting An Eight Metre Coal Horizon Con
Stooping Low Safety Factor Pillars At Goedehoop Colliery
Modelling Of Pillar Stability In Room And Pillar Mines
Pillar Optimization For Initial Design And Retreat Recovery
Application Of RMT's Remote Reading Telltale System To
Rock Mechanics Study Of Lateral Destressing For The Advance-
New Tools For Roof Support Evaluation And Design
Considerations For Using Roof Monitors In Underground Limest
Mine Roof Geology Information System (MRGIS)
Imaging Ahead Of Mining With Radio Imaging Method (RIM-IV) I
Geophysics For The Detection Of Abandoned Mine Workings
Investigation Of Seam Thickness And Seam Splitting Within A
Determination Of Rock Strength Properties Using Geophysical
RQD from the Barrel to the Box: Weatherability May be a Bett
A probabilistic approach to ground support design in undergr
The Requirements of a Database to Store Geotechnical Data to
Variation of Horizontal Stresses and Strains in Mines in Bed
Geotechnical Planning Basis for the Optimization of Workings
Tensile roof failure arising from horizontal compressive str
Study of load transfer capacity of bolts using short encapsu
Intersection Stability and Tensioned Bolting
Premature Rock Bolt Failure Through Stress Corrosion Crackin
Short-encapsulation Pull Tests for Roof Bolt Evaluation at a
Field Test with Strain-gauged Friction Bolts at the Gold Hun
Directional Rock Bolt Pullout Tests as Index Tests for Estim
Eclipse Bolting System
The Application of Pre-tensioned Grouted Tendons at Harworth
Investigation into the Extent and Mechanisms of Gloving and
Developments in Improving the Standard of Installation and B
Development of Geotechnical Procedures for the Analysis of M
Recent Developments in the Use of Seismic Tomography in Long
Pumpable Roof Supports: Developing Design Criteria by Measur
Design Considerations of the Secondary Roof Support for Long
The Effect of Standing Support Stiffness on Primary and Seco
Numerical Modeling of the U1A Complex at the Nevada Test Sit
Rock Mechanics and the Analysis of Underground Mine Stabilit
A Study of Potential Fault Reactivation and Water Intrusion
The Elimination of Rock-fall Fatalities in Ontario Hardrock
Root Causes of Groundfall Related Incidents in U.S. Mining I
Analysis on the Dynamics of Mining Subsidence in Range of a
Mitigating Subsidence Influences on Residential Structures C
Influences of Longwall Subsidence on a Guyed Steel Tower - A
Surface Movement of Super-wide Longwall Panels Using Top-coa
New Approach to Evaluate the Stability of Yield Pillars
Experimental Study of Acoustic Emission Characteristics for