If you have access to OneMine as part of a member benefit, log in through your member association website for a seamless user experience.
|The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.|
Additional chapters/articles from the SME-ICGCM book 22nd International Conference on Ground Control in Mining (ICGCM) 22nd
|Pillar Design and Roof Support for Controlling Longwall Head||Stress Analysis and Support Design for Longwall Mine-Through||The Utilisation of Numerical Modelling to Predict Water and||Longwall Roof Fall Prediction and Shield Support Recommendat||Comparison Of Multiple And Single Entry Roadways For Highly||Numerical Modeling Of Longwalls In Deep Coal Mines||The Characteristics Of Mining-Induced Fractures In Overlying||Design And Experience Of Total Extraction Room And Pillar Op||Using Site Case Histories Of Multiple Seam Coal Mining To Ad||Mining Method For Extracting An Eight Metre Coal Horizon Con||Stooping Low Safety Factor Pillars At Goedehoop Colliery||Modelling Of Pillar Stability In Room And Pillar Mines||Pillar Optimization For Initial Design And Retreat Recovery||Application Of RMT's Remote Reading Telltale System To||Rock Mechanics Study Of Lateral Destressing For The Advance-||New Tools For Roof Support Evaluation And Design||Considerations For Using Roof Monitors In Underground Limest||Mine Roof Geology Information System (MRGIS)||Imaging Ahead Of Mining With Radio Imaging Method (RIM-IV) I||Geophysics For The Detection Of Abandoned Mine Workings||Investigation Of Seam Thickness And Seam Splitting Within A||Determination Of Rock Strength Properties Using Geophysical||RQD from the Barrel to the Box: Weatherability May be a Bett||A probabilistic approach to ground support design in undergr||The Requirements of a Database to Store Geotechnical Data to||Variation of Horizontal Stresses and Strains in Mines in Bed||Geotechnical Planning Basis for the Optimization of Workings||Tensile roof failure arising from horizontal compressive str||Study of load transfer capacity of bolts using short encapsu||Intersection Stability and Tensioned Bolting||Premature Rock Bolt Failure Through Stress Corrosion Crackin||Short-encapsulation Pull Tests for Roof Bolt Evaluation at a||Field Test with Strain-gauged Friction Bolts at the Gold Hun||Directional Rock Bolt Pullout Tests as Index Tests for Estim||Eclipse Bolting System||The Application of Pre-tensioned Grouted Tendons at Harworth||Investigation into the Extent and Mechanisms of Gloving and||Developments in Improving the Standard of Installation and B||Development of Geotechnical Procedures for the Analysis of M||Recent Developments in the Use of Seismic Tomography in Long||Pumpable Roof Supports: Developing Design Criteria by Measur||Design Considerations of the Secondary Roof Support for Long||The Effect of Standing Support Stiffness on Primary and Seco||Numerical Modeling of the U1A Complex at the Nevada Test Sit||Rock Mechanics and the Analysis of Underground Mine Stabilit||A Study of Potential Fault Reactivation and Water Intrusion||The Elimination of Rock-fall Fatalities in Ontario Hardrock||Root Causes of Groundfall Related Incidents in U.S. Mining I||Analysis on the Dynamics of Mining Subsidence in Range of a||Mitigating Subsidence Influences on Residential Structures C||Influences of Longwall Subsidence on a Guyed Steel Tower - A||Surface Movement of Super-wide Longwall Panels Using Top-coa||New Approach to Evaluate the Stability of Yield Pillars||Experimental Study of Acoustic Emission Characteristics for|