Deep Cover Pillar Extraction in the U.S. Coalfields

Chase, Frank
Organization: International Conference on Ground Control in Mining
Pages: 13
Publication Date: Jan 1, 2002
Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF's) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF's, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.
Full Article Download:
(3492 kb)

Additional chapters/articles from the SME-ICGCM book Proceedings 21st International Conference on Ground Control in Mining

Pre-Driven Experimental Longwall Recovery Room Under Weak Ro
Longwall Mining-Induced Abutment Loads and Their Impacts on
Influence of Structural Stress Concentration and Structural
The NIOSH Shield Hydraulics Inspection and Evaluation of Leg
Study on Top-Coal Loss and the Optimum Drawing Interval of L
Stress Measurements for Safety Decisions in Longwall Coal
Re-Use of Rectangular Bolted Roadways in a Cover Depth > 100
Numerical Modeling of the Gob Loading Mechanism in Longwall
Deep Cover Pillar Extraction in the U.S. Coalfields
Evaluation of Pillar Recovery in Southern West Virginia
A Case History Investigation of Two Coal Bumps in the Southe
A Linear Coal Pillar Strength Formula for South African Coal
Anchorage Pull Testing for Fully Grouted Roof Bolts
Comparison of Some Aspects of Bolting Mechanisms Between Ful
Eclipse System Improves Resin Anchored Rebar Bolting
Design Considerations for Tensioned Bolts
Field Testing of the Fully Grouted Thrust Tensioned Bolts
Improvement in Pre-Tensioning of Strand Bolts in Australian
The Introduction of Roof Bolting to U.S. Underground Coal Mi
Support of Coal Mines in the United Kingdom
The Use of NDT Methods to Determine the Condition of Rockbol
Rockbolted Support of Retreat Longwall Gateroads at 1000m De
Roof Screening: Best Practices and Roof Bolting Machines
Numerical and Physical Modeling as Planning Tools for Rockbo
Stone Mine Design in Highly Fractured Rock
The Importance of Underground Stone Mine Roof Geology
Utilization of Ground-Penetrating Radar to Determine Roof Co
An Examination of the Loyalhanna Limestone's Structural
Highwall Stability in an Open Pit Stone Operation
Overview of Safety Considerations with Highwall Mining Opera
Highwall Monitoring to Combat Rockfall Accidents at Opencast
Seepage and Reinforcement Behavior of Grouting Into Slaking-
Floor Heave in Shallow Room-and-Pillar Mining
Analysis of a Stability Problem in an Underground Coal Mine
Comparison of Acoustic Emission and Stress Measurement Resul
Acoustic Scanner Analysis of Borehole Breakout to Define the
Estimating Rock Strengths Using Drilling Parameters During R
New developments with the coal mine roof rating
Application of geotechnical and geophysical parameters to im
Development of a Risk Rating System for Use in Underground C
Empirical and analytical design of large openings at a propo
Shear Mechanism for Mining-Induced Fractures Applied to Rock
Evaluating Techniques for Monitoring Rock Falls and Slope St
Developments in Sealant Support Systems for Ground Control
Stability Control of Clusters of Deep Openings Around Shaft
The Use of Pneumatic Stowing in Germany Considering Subsiden
A 3-D Semi-Analytical Method for Subsidence Prediction and S
Theory and Technology of Mining Subsidence Control by Grouti
Surface Subsidence Due to the Combined Effects of Undergroun