The Stress Measurement and Underground Engineering

Chu, Ding Xu
Organization: International Conference on Ground Control in Mining
Pages: 11
Publication Date: Jan 1, 1987
There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.
Full Article Download:
(2605 kb)

Additional chapters/articles from the SME-ICGCM book Proceedings 6th International Conference on Ground Control in Mining (ICGCM) 6th

Microseismic Monitoring of Mountain Bumps and Bounces: A Cas
Factors Influencing the Occurrence of Coal Pillar Bumps at
Longwall Pace Bursts and Inadequate Caving: A Came Study
Mine Layout Deign for Coal Bump Control
The Strong Outbursts of Coal and Gas in Coal Mines in China
Bock Bursts Occurrence. in the Coeur D'Alene Mining Dis
A History of Bock Burst Research in the Coeur D'Alene M
Chemical Destressing to Alleviate Rockbursts
Rockburst Control Measures at INCO's Creighton Mine
Prevention. Control and Management of Coal and Gas Outbursts
Application in Design for Close Proximity Multi-Seem Mining
Geologic Conditions Affecting Mineability in the Jane Mine.
Analysis of Cutter Roof Using the Boundary Element Method
A Novel Ground Control Program at Plateau Mining Company
Evaluation of Anchorage Integrity for Grouted Bolts in Weak
STRATA III ? A Full-Spectrum Roof Control Concept
Study of Ground Movement Over a Longwall Mine
Field Measurements of Overburden and Chain Pillar Response t
A Method for Sizing Longwall Pillars Based on Field Measurem
Aspects of Chain Pillar Design in Relation to Longwall Minin
The Initial Collapse of the Overburden Over Longwall Panels
Monitoring and Prediction of Ground Movements Above Undergro
Mechanisms of Chimney Subsidence Over Abandoned Coal Mines
Time-dependent Behavior of Immediate Weak Floor Strata from
The Significance of Specimen Stiffness and Post Yield Charac
Frictional Properties of Rock Applied to Mining Excavations
Ice Pillars, Packwalls, and Brattices
Investigation of Subsidence Over AML: A Case Study
Deign of Support System for Mining Tunnels in Carboniferous
Support of Tunnels in South African Gold Mines
The Stress Measurement and Underground Engineering
Field Measurements Of Overburden And Chain Pillar Response T